Home > Unable To > General Misprint Error

General Misprint Error

Contents

I found the paper pickup solenoid had sticky stuff on it and was sticking after a long print. I am beginning to think that the problem is in one of the controller boards, but that gets over my head. Check/reseat cable between DC Controller and Formatter PCA. 56 ERROR IID, IIID Only: 1. It can also occur when the page does not feed past a sensor in the time alotted and the printer thinks it is a larger size.The 49 errors are more mysterious have a peek at these guys

You've made my day!! Reseat connector J201 on Sensor PCA. 3. Report the results so further advice can be given. HP is going to replace the fuser under warranty once it is reinstated. 0 LVL 1 Overall: Level 1 Printers and Scanners 1 Message Author Comment by:tcampbell_nc2009-12-08 Update: HP Warranty

41.03 Error

Bad 47W resistor (1/4W) on the Fuser Safety PCA (connector J107 on the Fuser Safety PCA). (P/N FF1-3872-000.) 2. Other times you tell it to print (even immediately after printing something else) and ithe printer sits there churning for two to three minutes before paper starts being pilled through. If necessary, turn the product off and then on. I heard the gears turning, and turning, and turning...

I cleaned off all the stickiness and made it worse- made a clank noise and got jammed all the time then. It might also be called something like "factory reset" or "non-volatile memory reset". 0 LVL 1 Overall: Level 1 Printers and Scanners 1 Message Author Comment by:tcampbell_nc2009-10-23 What will a Replace both at same time. At that same suctomer site, we still have an HP 4000 (manufactured in October of 1998) still as a production printer.

In our case, that is true MOST of the time. Hp 4250 Unable To Store Job At Printer Trying to print envelope in duplex mode (envelopes cannot be duplexed). During that time all motors will be running, just as if it were already printing. http://fixyourownprinter.com/posts/67029 By using this site, you accept the Terms of Use and Rules of Participation Sign Up Login Add Question unknown asked Oct 18, 2011 at 6:08am 0 Unknown Printer LaserJet

I kept getting 41.03.00 and 13.06 errors. They felt that the fuser was the problem. by Anonymous on Jan 30, 2006 at 7:54am Add comment Please sign in to comment 0 The 41.5 error is a paper feed error so it is possible you have a We have also set the "Sleep" time (I am assuming this is the power saving after a period of inactivity) to 2 hours.

Hp 4250 Unable To Store Job At Printer

Comment Submit Your Comment By clicking you are agreeing to Experts Exchange's Terms of Use. why not find out more Such opinions may not be accurate and they are to be used at your own risk. 41.03 Error plz help! Unable To Store Job At Printer Insufficient Disk Space For This Job I found the paper pickup solenoid had sticky stuff on it and was sticking after a long print.

No toner cartridge. 3. Get 1:1 Help Now Advertise Here Enjoyed your answer? I still do not have na answer to my original question which is: why does it cycle so much when a print job is sent. If the DHCP address is not what you require, you will have to set the correct address manually. 0 LVL 1 Overall: Level 1 Printers and Scanners 1 Message Author Hp Printer Error Codes

They are printing directly to the printer (TCP/IP ports on the workstations) due to WordPerfect being the primary word processor. DC Power Supply/Main motor driver malfunction. IIP, IIP+, IIIP Only: 1. 57 Error Unit 1 - Incompatible memory card in top slot. 2. 57 Error Unit 2 - Incompatible memory card in bottom slot. 57.x ERROR (IIISi/4Si At full tilt, and while heating the fuser, the printer will consume about 1kW.

I've got the Q3955-60003 board and I was told these go bad often. Check Duplex Shift Plate for correct operation. 2. This permitted the printer to start printing again.

You clean off all the residue underneath the strike plate and you have to replace it with something.

Regards. 0 LVL 37 Overall: Level 37 Printers and Scanners 37 Peripherals 11 Message Active today Expert Comment by:hdhondt2009-10-18 Printer specs, especially speeds, given by the manufacturer are always the Reply 0 0 npavans4015 Honor Student Posts: 3 Member Since: ‎10-02-2012 Message 5 of 8 (11,149 Views) Report Inappropriate Content Re: P4015 Printer- Error & sudden slow priting & heavy sound Defective fan, PS4 or PS5 4. Press OK and if that doesn't clear the message try the time honoured turn off and turn on again. 41.02.00 ErrorBeam detect misprint The manual says verify that the toner cartridge

Before that, no complaints.... Report back those results so I can give you further advice. Defective Paper Control PCA on the Paper Feed Assembly. 4L Only: 1. Power the printer back on and watch for the memory count to begin3.

Inspect toner level sensor connector for damage. 4. Hopefully the problem will evaporate. 41.X Error 41.X ERROR This usually means that "a temporary printing error occurred." For help press ? Then i put a small piece of rubber at the tip of the solenoid to stop it clanking. On the P4014 series the formatter self tests to some extent, and should be flashing the heartbeat light and responding to web-server requests (if it is, that suggests it hasn't failed)

Optional I/O card is not connected to an active LAN. 3. Check/replace SIMMs. 62.x memory error 4000/4050/4100/5000/8000/8100 only: 62.x where x = Dimm slot, Check/replace DIMMs. 63 SERVICE 1. a. If you have any questions, then please Write a Comment below!

Codes other than 41.3 might mean this, (more below). This printer has 5 trays in use, so I must utilize a driver that knows how to handle the trays. Check RAM expansion card, reseat if necessary. 2. Turned off printer and wait for 30 seconds, turned on back again and viola everything is working normal again.Carlos by [emailprotected] on Apr 6, 2016 at 7:43am Add comment Please sign

Get trending threat insights on hackers, exploits, and suspicious IP addresses delivered to your inbox with our free Cyber Daily. Replace cable, AC Power Module to DC Controller, connector J208. (P/N RG1-0912-000.) IIP, IIP+, IIIP Only: 1. Other Research Frustrated with this, in 2013 I used Recoll to search our internal collection of information. Computing.Net and Purch hereby disclaim all responsibility and liability for the content of Computing.Net and its accuracy.

I have just downloaded the PCL 6 driver, but we have had bad experiences in the past using PCL 6 for other HP Printers.