Electronic Range Control, ERC, Electronic Oven Control, EOC, control board, and clock all refer to the same part. F1 Failed transistor in control if you get this code the control board needs replacing. Also check for any causes of high resistance in the oven temperature sensor circuit. FD Shorted meat probe Problem could be with the probe, the receptacle, or probe circuit. http://blogeurope.net/ge-oven/ge-oven-function-error-codes.php
UE - Unbalance Switch Error - Open lid and re-balance laundry manually. If it isn’t, the problem is the temperature sensor.Or it might not be the temperature sensor.Sure, it is then a wiring fault or control board fault.Now we’re back to reboot and Replace faulty part. 7E - Water Supply Error - Press 'Power' button and check wiring harness, water valve, pressure sensor switch, and circuit board for defects. Anmelden Wird geladen... this content
FC - Door Lock Circuit - Check wiring and test switches. C8 - Detergent Cup Blocked - Check for debris around detergent cup. Resistance should be 30k ohms to 50k ohms at room temperature. · Look for pinched wire. · Look for condensation or contamination of receptacle or nearby installation. F8 EEPROM data error.
skip navigation Click to call Click to Chat 1-800-491-3457 Login Register Order Status Feedback Get Manuals Repair Help Expert Q & A Recently Viewed My Models (0) Main Menu Recently Viewed C3 - Will Not Drain - This occurs when dishwasher is not able to switch to the drain mode. Reply With Quote « Previous Thread | Next Thread » Thread Information Users Browsing this Thread There are currently 1 users browsing this thread. (0 members and 1 guests) Bookmarks Bookmarks Ge Error Codes Washer Contact Us DoItYourself.com Mobile Site Privacy Statement Top All times are GMT -7.
Personal Reminder: Buckle Up & Drive Safely. "The Life You Save, May Be Your Own." Regards and Good Luck. If the resistance is not within the range mentioned above, then replace the sensor. Hinzufügen Möchtest du dieses Video später noch einmal ansehen?
Replace if defective.
F-9 Door lock safety circuit on ERC sensed Replace the door latch assembly F-C or F-0 Communication error between boards Replace the relay board. Ge Oven Error Codes F7 E6 The code should be cleared, but if the code ever comes back replace control board. Remember: Oven control (ERC) measures resistance of sensor circuit , not actual oven temperature. Keep objects clear of cup when loading dishwasher.
Points valid for 14 days. See Range - Oven Door Won't Unlock.Loc DoorIf this code is flashing in the display of your range or oven, and the self-clean cycle has not been selected.LOCChild lockout is a Ge Fault Codes CT Sat7:00 a.m. - 9:00 p.m.CT Sun7:30 a.m. - 9:00 p.m.CT Chat Local Store Availability Enter your zip code Find Store Sears PartsDirect uses your location to provide local availability Ge Oven Error Codes F3 Remember: Oven control (ERC) measures resistance of sensor circuit , not actual oven temperature.
Thank A Veteran. More about the author If so, its grounded out and replace sensor and/or sensor wires, if its not grounded out replace control board. If the resistance isn't 1080 ohms at 70F, replace the oven temperature sensor. Keypads and control boards can be purchased at AppliancePartsPros.com. Ge Oven F9 Error
Wird geladen... Anmelden Teilen Mehr Melden Möchtest du dieses Video melden? Be sure to turn the range or oven off at the breaker again when you have finished. http://blogeurope.net/ge-oven/ge-cooktop-function-error.php If no over temperature condition occurred: Look for a high resistance connection or any other cause of high resistance in the oven temperature sensor circuit.
F2 The temperature in the oven reached over 590 degrees Fahrenheit with the door unlocked or 930 degrees Fahrenheit with the door locked. F76 Ge Oven Check wiring and test operation of switches. Sign in and keep model in your profile permanently Don't have a profile?
C7 - Temperature Sensor Bad - Replace temperature sensor (remove door to access panel, sensor should be located inside the door). If you don’t find any loose connections, I would recommend changing the sensor even if it checks good cause it could be intermitting. F7 This fault code stands for shorted function key. Ge Oven Error Code F7 F8 Shorted meat probe Problem could be with the probe, the receptacle, or probe circuit.
If error persists, check electrical connections to dishwasher and electronic control (control board). Replace the oven temperature sensor wire harness if damaged. Reconnect any loose wires in the oven door lock circuit. news FF Loss of door motor safety switch Replace the oven control (also called clock or ERC).
Kansas City, KS "Robin went above and beyond the call to assist me and I was very impressed." Val T. Check the probe for pinched wires and make sure there is no condensation or contamination on receptacle. F5 - Loss of Relay Drive Circuit - If error cannot be cancelled by selecting the 'cancel' function, the control board (clock) will need to be replaced. Generic Fault Codes: Fault Code Interpretation Components To Check F-1 Communication error between touch pad and ERC (clock) Replace the touch pad or clock.
First you need to check the sensor, disconnect power, pull the range or oven out then take off the back cover. Check drain line and drain valve in pump for debris and blockage. All of our chat agents are currently assisting other customers. Contact an installer or electrician to correct the mis-wire and the oven will function normally.Unlock DoorThis code appears when the door will not unlock after a self clean cycle.
It is okay to cycle the breaker and turn the range back on long enough to use the surface units. Close
In this section of my range repair guide I have a full list of the fault codes along with the steps for you to follow in order to repair your oven. Cannot be applied to previous purchases and cannot be redeemed for cash. All rights reserved. Disconnect power for more than 30 seconds then reconnect power.
Replace probe if all else checks out ok.