Home > Fuser Error > Fuser Error Elite 21

Fuser Error Elite 21

I cannot recall the last time something like that happened in politics or religion." (1987) -- Carl Sagan Edited 1 time(s). Load the correct paper size into the tray. fullThe specified output bin is full. How do I fix it? Did you mean? his comment is here

It's problem with fuser. Im not trying to be mean or anything but thats my opinion. Thanks for the help. - atlantis1 I have a problem with my printer xerox n2125. The Fuser is held in place by 2 black thumb screws – remove these and pull the Fuser out. http://www.fixya.com/support/t4074710-gcc_21n_fuser_error

Restart printer, contact service if error persists. The display should come to “Ready” and the printer will be ready to resume printing. 10-12 Error/Status MessagesIn the event that a printer error occurs, the Elite 21 printer will display Wait at least 30 minutes to let the fuser cool down before servicing the fuser.2. Are reconditioned fusers reliable?  A new fuser for this machine is about $300.

is size of the printer an issue? Be sure to upgrade the firmware on the printer to the current revision as HP has made some adjustments to the DC controller on this printer to extend fuser life. fuser, the part of a laser printer that melts the toner onto the medium. Given the fact that its happening in the morning though sounds like a power struggle.

Can you help? After getting the fuser failure on the new one I pull out the older one to replace it, but as soon as it gets booted up I get the fuser failure Remove the 4 screws holding the top on and remove the top. Power off, reseat the fuser and then start again, if error repeats replace the fuser.

The ROS (laser) unit of the printer is experiencing an error. This particular question helped even though it wasn't the intent of the original poster.My printer was getting flaky, with the fuser error coming more and more until I could no longer just repaired today).Thank you everyone who posted here from all the way back in 2006 or so. Do you have any information where I can by the lamp and how much it cost.

I get the "engine fuser low hear error" What can I do? Paper has jammed while feeding. RestartFan motor errorprinter, contact service if error persists.Service requiredThe NVM (non-volatilememory) of the printer is experiencing anNVM errorerror. Close the cover.Load The printer requires the specified paper size in the specified trayto print the job.

All other copyrights are property of their respective holders. http://blogeurope.net/fuser-error/fuser-error-501.php I live in Montenegro. - Anonymous I have a problem with my xerox n2125 fuser. Fuser Error 50.1 Fuser May 12, 2008 | HP LaserJet 2840 All-In-One Printer 4 Answers Hp 4350 error code 50.3 I have just changed the fuser unit and the printer is Reply 0 0 « Message Listing « Previous Topic Next Topic » Related Documents HP Printers - Using HP Diagnostic Tools for HP Printers in WindowsHP Printers - After Windows 10

I tried booting it without the network cable. I tried booting it without the network cable. but when warm, it would work fine. http://blogeurope.net/fuser-error/fuser-error-hp.php Replace the thermistor, reassemble and reinstall the Fuser, and you should have a working printer.

Insert the tray and the job will print.No env. When you install a replacement Transfer belt (it has it's own counter chip) that resets the transfer belt pagecount, and as a result clears any transfer belt life related warnings/errors. HiMy N2125 gives me an "Fuser problem, power OFF" error.The heater should be OK, I suspect either the weird blue diode or the temp.

We are independent repair agency.

They want you to play mind-reader with them. Error Message Error Duplex unit Error Upper bin unit Error Face-up bin Error Envelope Feeder Service required Fuser error Service required ROS motor error Service required Main motor error Service required Close face-up bin, or send job to standard bin. Restart printer, contact service if error persists.Service requiredThe ROS (laser) unit of the printer is experiencing an error.ROS motor errorRestart printer, contact service if error persists.Service requiredThe main motor of the

View Solution. Mar 12, 2009 | HP LaserJet 4700 Printer 2 Answers Fuser Error 50.1 Fuser is hot. Restore password × Upload manual upload from disk upload from url Thank you for your help! http://blogeurope.net/fuser-error/fuser-error.php But really its not heating up in time and after it started the process and fails it gets to the point where it can get to its correct output.

by [eric] on May 15, 2007 at 1:27pm Add comment Please sign in to comment I found a place - partsmart-corp that has them for 13 bucks, at least for now. Where to get? It consists of a hot roller and a back-up roller. Sign up!