Home > Fuser Error > Fuser Error 50.5

Fuser Error 50.5

Thank you! Register · Log In HP Support Forum Home > Printers > Inkjet > 50.5 Fuser Error with new fuser installed HP Support Forums Join in the conversation. Printers were originally used for interfacing with the operator, not necessarily for printing copy or pictures. Replace Fusing Assembly 3.  Replace DC Controller  4. Make sure that the Fusing Assembly is installed correctly and is fully seated into its connectors (no bent pins or pins outside their receptacles). 2. http://blogeurope.net/fuser-error/fuser-error-501.php

The square opening at the upper rear corner on the right side plastic panel is the engine test access. 1. Fuser Error Code 50.1: Low fuser temperature 50.2: Fuser warm-up service 50.3: High fuser temperature 50.4: Faulty fuser 50.5: Inconsistent fuser (verify voltage model) Service Manual Recommended Action Turn the printer While grasping onto both sides of the fuser, push the blue levers upward and pull the fuser straight out. HP say: Verify that the connection to connector J82 on the DC controller PCA is firmly seated.

If the part number on the fuser is the exact same as the one you removed, try powering off the printer and unplugging it from the power source for a few As a safety precaution wait 30 minutes for the fuser to cool before proceeding. Leave a Reply Cancel reply Your email address will not be published.

If the fuser does not click into place you run the risk of wearing out both the fuser and the gears that drive the fuser prematurely. Unplug 3 LVPS connectors 2. Sorry, I'm sure your nice people. Discussion Boards Open Menu Discussion Boards Open Menu Welcome to the Forum!

If you experience any of the above issues with the fuser replacement it (RG5-6532) along with the power supply. Talk to the provider you purchased the fuser from - have them send you a new one. 0 Message Author Closing Comment by:remcjr2007-12-18 Yes this was the problem and the Physically the fuser fits, but the printer shuts it down. All rights reserved.

As you finish projects in Quip, the work remains, easily accessible to all team members, new and old. - Increase transparency - Onboard new hires faster - Access from mobile/offline Try Join the community of 500,000 technology professionals and ask your questions. After verifying the problem is related to the AC power supply, check the fuser for common wear and tear in case the fuser also needs to be replaced. Privacy Policy Site Map Support Terms of Use On Sale About Us Contact Us Order Status FREE TECH SUPPORT (877) 755-5300 Login My Cart (0) Printers Printer Supplies Printer Parts Printer

Reconnect the connectors of the fuser control PCA (J303, J305), low-voltage power-supply unit (J6), and the DC controller PCA (J102, J207). 3. https://mindmachine.co.uk/products/HP_Texts/HP_LJ-P4010_-_ops_error-50.5_01.html Set the output bin cover aside. Solved Fuser error 50.5 Posted on 2007-12-13 Printers and Scanners 1 Verified Solution 5 Comments 8,363 Views Last Modified: 2013-12-15 I just installed a new maintanance kit and after installing it Turn Printer off and wait 5 minutes letting fuser assembly too cool,  then turn back on..  2.

See the catalogue. this content Maintenance Kit should installed every 350,000 pages (C3914-69001). In … Printers and Scanners How to Request Attention Video by: Kline Need more eyes on your posted question? There are probably very few 5SI and CLJ-4500 printers left in service - you cant get the parts.

Steps for cold reset here: https://www.laserquipt.com/support/idx/0/121/article/Cold-Reset-Steps-for-HP-Printers-.html 0 LVL 27 Overall: Level 27 Printers and Scanners 13 Message Expert Comment by:michko2007-12-13 Oh, yes, forgot to add, if the above doesn't solve, Replace Fusing Assembly 3.  Replace DC Controller  4. Odds are higher of a bad fuser if it was a remanufactured. http://blogeurope.net/fuser-error/fuser-error-50-9.php Solution: 1.

Join & Ask a Question Need Help in Real-Time? By the time you get that "50.5" error you opened the box and installed the fuser in the wrong printer. There will be another video to explain how to put the final p… MS Office Office 365 MS Access Advertise Here 772 members asked questions and received personalized solutions in the

Find maintenence kitInstallation instructions Home Page Technical Resources Lexmark Error Codes HP Error Codes Tech Support Blog HP Drivers Lexmark Drivers Terms & Conditions Product Conditions Definitions Web Order

Anyone have any ideas how to fix the problem? socalprinterservices Ad by a US maintenance company using the error codes as an attractor but giving no information In practice there were just a couple of pages of scarcely relevant stuff The best way to determine which fuser you have is to pull the fuser out of your printer and check the barcode label on the fuser. If the incorrect fuser goes in, you can get a 50.5 error (or a 13.20 error in some cases) when you power on the printer.

The 6015 take the 110v, not the 220v that we received. Solution: 1. eCommerce Solution : k-eCommerce ERROR The requested URL could not be retrieved The following error was encountered while trying to retrieve the URL: http://0.0.0.10/ Connection to 0.0.0.10 failed. http://blogeurope.net/fuser-error/fuser-error-hp.php and may not be used without advance written permission of PrinterTechs.com, Inc.

Rare, but it does happen. Remove the Formatter PCA 2. Once you have the fuser out, check the fuser's barcode label for the part # and see if the part # matches with your model printer. Look for bent pins or debris.

We gather from customers that many suppliers will not take things bought in error back. Once you have correct fuser matched up with your model, install the replacement fuser by inserting it and aligning the left side first. I'm sure it has backlinks, it will once have been best of breed. The gears should rotate smoothly.

The system returned: (22) Invalid argument The remote host or network may be down. The argument that "Marks and Spencers just take things back" isn't helpful, they make a huge margin on clothes and anyway that policy has changed. Inspect the fusing assembly connectors, at the front of the assembly, and the connectors on the high-voltage power supply PCA. Learn how to create a query and then a grouped report using the wizard.

Sometimes a front cover gets changed since 4200 or 4300 front cover will fit. So you can get the right fuser for what you only thought was the right printer. Low Voltage Power Supply 1. Clean or straighten the pins if necessary. This problem was (and remains) notorious with LJ 4200/ 4300/ 4250 / 4350 printers where the fusers look the same but are different backpage.com Just an add.

Remove 5 screws 2. Bookmark the permalink. All rights reserved.