Home > Frigidaire Oven > Frigidaire Stove Error Codes

Frigidaire Stove Error Codes

Contents

I checked the sensor and and it checked at 1100. What is wrong with the oven temperature and what is the difference between the set and actual temperatures? Kansas City, KS "Robin went above and beyond the call to assist me and I was very impressed." Val T. What does F31 error code indicate on a Frigidaire gas range? Report This by Manage My Life December 20th, 2008 We had oven temperature problems and had technician come out and have a peek here

I bought laser thermometer for the oven and it would verify the lower temperature. Check the temperature sensor resistance as described previously. Very likely the EOC you received is defective. Thanks so much for your time and help!

Frigidaire Oven F11 Error Code

Wird geladen... It measured 1050 ohms, we then tested it back at the EOC, same reading. Your satisfaction is important to Sears. A defective temperature sensor can also cause this problem.

P.S. I have a Frigidaire model FFGF3047LSF. Replace the electronic control board. Frigidaire Oven F10 Reset I did this and it didn't work.

In such situation the only solution is to replace the EOC. Frigidaire Oven F10 Error https://www.dropbox.com/s/afvfo1xuvvrlsef/Electric%20slide-in%20range%20-%20control%20panel%20and%20EOC%20removal%20part%201.doc?dl=0 https://www.dropbox.com/s/uyrdx536z25aege/Electric%20slide-in%20range%20-%20control%20panel%20and%20EOC%20removal%20part%202.doc?dl=0 https://www.dropbox.com/s/ntcglkxlq82agdk/Electric%20slide-in%20range%20-%20control%20panel%20and%20EOC%20removal%20part%203.doc?dl=0 Keep me updated. Check the upper oven temperature sensor by measuring resistance between two wires connected to the pin 9 and 10 at the plug P27. Thank you in advance!

Du kannst diese Einstellung unten ändern. Frigidaire Stove Error Codes F7 Hey. Find Parts Appliance Repair Appliance Repair Dishwasher Repair Garbage Disposer Repair Dryer Repair Freezer Repair Microwave Repair Range / Oven Repair Range Hood Repair Refrigerator Repair Trash Compactor Repair Washer Repair Let the oven cool down and restart the function.

Frigidaire Oven F10 Error

Much appreciated, Max Gene // Sep 6, 2015 at 9:34 pm Hi Max, Quick answer on quick question. Get all the details Close 365 Day Return Policy You may return an unused and uninstalled part in its original packaging. Frigidaire Oven F11 Error Code If the lock motor, switches and wiring are good, the EOC would need to be replaced. Frigidaire Oven Error Code F30 It's possible that your range is not heating to the temperature that you set it to, or the control board may be reading the temperature incorrectly.

The part number for the EOC is 316418521 Good luck. http://blogeurope.net/frigidaire-oven/frigidaire-stove-f10-error.php Valerie // Sep 7, 2015 at 8:00 am Hello again Gene! Maybe worthy of note - I did not piece together everything (burners not screwed back in; metal piece covering the wires in back not screwed in). Measure the resistance between these wires. Frigidaire Eoc

Items received damaged must be reported within 10 days of receipt. What does this mean please? Otherwise if the wire harnesses are good, the user interface board would need to be replaced. http://blogeurope.net/frigidaire-oven/frigidaire-stove-error-f30.php BUT oven not heating up.

If the oven will continue to heat, the oven relay board would need to replaced. What Does F10 Mean On A Frigidaire Oven Happy holidays! Jacqui // Jan 3, 2015 at 3:06 am Ok so with your website I've figured out what is wrong with my stove…it won't stop beeping and my problem is won't be

I decided to pull off the rear cover and take a peak and found a portion of the Oven Control Board was burnt/charred.

Sounds like the EOC is the culprit. A wiring failure could also cause this problem. The part number for the EOC is 316557205 The part number for the overlay is 316419303 Good luck and keep us posted. Frigidaire Oven F10 Beeping Close Automatic Reorder Details Receive free shipping on all automatic reorders with subscription Note: This offer is only valid in the contiguous U.S.

Starts beeping then stops and starts again after a while. Thanks, Kevin Gene // Jun 6, 2014 at 5:35 pm Hello Kevin. Larry Smith // May 20, 2015 at 11:05 am Hi Gene, I have an F10 on a PLEB30s9dca Fridg. http://blogeurope.net/frigidaire-oven/frigidaire-f10-stove-error.php F3 or F30 - Open/shorted sensor (RTD probe) connection.

I disconnected the stove and plugged it back in, the broil and oven elements still do not work and they visibly appear fine. Gene. Thank you for your help. Diese Funktion ist zurzeit nicht verfügbar.

Keep me posted. Thank you for your good words. This seems to have happened randomly after years of fine operation. You can try to use the old one but if you damage it, the part number for the overlay is 316419700 Good luck and keep us posted.

If there is no continuity, the heating element is the culprit. You may want to replace it together with the overlay. When we set a temperature at say 350, it beeps between 25 to 50 degrees less (we used an oven thermometer for testing). The motor does not stop rotating.  Press stop key.

Sign up here Shop Your Way members get $10 in points on any PartsDirect purchase with coupon code SYW10. Gene. If the oven is overheating, disconnect power. And the more you shop, the faster the benefits add up.

The normal reading suppose to be about 1100 Ohms. Built-in ... Your question was published, help is on its way!