Home > Frigidaire Oven > Frigidaire Stove Error Code F30

Frigidaire Stove Error Code F30

Contents

It measured 1050 ohms, we then tested it back at the EOC, same reading. Thus the solution is to replace it. The part number for the EOC is 316207603 The part number for the overlay is 316243301 Good luck. Craig // Dec 24, 2014 at 6:30 am Hi Gene, Thanks for the information on this site. http://blogeurope.net/frigidaire-oven/frigidaire-stove-f10-error-code.php

Tags: Oven error codes 232 responses so far ↓ Ron Hirtz // Nov 16, 2013 at 7:26 pm I have the F10 error code ohm reading at the plug into the Black ... Disconnect power, wait 10 seconds and reapply power. Only thing to add is that the thermal breakers can have an intermittent issue (probably with reset (red) switch).

Frigidaire Stove F11 Error

This pricey gizmo runs a little over $200, but it's easy to change. Once refreshed the error should no longer be displayed. Resolve error code by : Unplug the unit or turn the circuit breaker off for 60 seconds. Restore the power to the appliance by There is a separate membrane switch in your range which would need to be replaced in such situation.

Valerie Gene // Sep 7, 2015 at 9:06 pm Hello Valerie, Thank you for your question. Thanks again. Our cooking manuals cover a wide selection of gas and electric models of ovens and cook tops, ranges and stoves, self-cleaners and convection ovens. Eoc Frigidaire Oven If not, I understand that it is likely either the thermometer or the panel.

replaced EOC. F10 Error On Frigidaire Oven George Gene // Dec 19, 2014 at 1:01 pm Hi George, You are welcome and thank you for the feedback. Gene. Gene.

Gene. Frigidaire Stove Beeping F10 I have a Frigidaire range, model #PLEF398DCH. The black potentiometer should have a resistance of 10KΩ. In such situation the only solution is to replace the EOC.

F10 Error On Frigidaire Oven

Remove the rear panel and locate two small power supply boards right next to the oven relay board. In order to access it you would need to remove the oven from the cabinet. Frigidaire Stove F11 Error Is there a way to silence the alarm so we can still use the range? Frigidaire Oven Error Codes Oven temperature sensor - What a common sensor or temp sensor looks like.

In order to provide most accurate advice I need the complete model number of the oven. http://blogeurope.net/frigidaire-oven/frigidaire-stove-f10-error.php I do not think they will keep it available for more than five years since production started. Brands: Kenmore Frigidaire Categories: Washing Machines Microwave Ovens Kitchen Ranges Ovens Unanswered Questions Ask a Question Usually answered in minutes! Gene. Frigidaire Oven Rtd Sensor Probe

Gene. Rachel // Mar 14, 2015 at 8:14 am Hello, My range is showing F10 error code since this morning. Thank you, Gene. http://blogeurope.net/frigidaire-oven/frigidaire-stove-error-f30.php Repairclinic.com Appliance Newsletters Purchase Info for Appliance Parts & Manuals » Need Parts?

Valerie // Apr 24, 2015 at 7:00 am Hi Gene, I am having problems again and before I order on my diagnosis, I wanted your confirmation. Frigidaire Oven F10 Reset If this error code shown while the oven was in day time mode, the EOC would need to be replaced. Gene.

Sounds like it's time for new range.

The F11 error code means that control has sensed a shorted keypad. The user interface board is mounted on the back of the range, just below the control panel. Keep me posted. Frigidaire Oven F31 Error This is why we were back to thinking that the electronics weren't working.

CT Sun 7:30 a.m. - 9:00 p.m. It may have an open connection or just plain defective sensor. IMPORTANT DISCLAIMER: The Author of this web site assumes no responsibility for inconveniences or damages resulting from use of the information he supplies. http://blogeurope.net/frigidaire-oven/frigidaire-f10-stove-error.php See Details Frigidaire FFEF3018LQ 5.3 cu.

Have a manual for Kitchen Ranges? do you still suspect the relay board 316443925 ? Press UPPER OVEN or LOWER OVEN to select oven. 2. If there is a such part, replace it.

Measure the resistance between the wires connected to these pins. Frank // Feb 27, 2015 at 5:51 pm Hi Gene, You helped me back in November with a F10 error. It appears I do have a separate power/relay board, EOC board and a power supply board. Freestanding ...

Press BAKE for 6 seconds. “UPO 00” will appear in the display. 3. The part with the key pads you see, is nothing else but the overlay which is glued to the EOC. If you get an open or short by measuring at the P5 plug, the issue is either the probe OR the thermal breakers. Sorry for the delay.

Thank you for your help. Try resetting the unit and see if the error code will clear. I get a f10 error code only on the top oven. Credentials confirmed by a Fortune 500 verification firm.

Use the "Search by the model number" link bellow to see if your range has a such part. Sorry for such sad news. The part number for the EOC 316455410 Thank you for your question.