Home > Frigidaire Oven > Frigidaire Range Error Code F10

Frigidaire Range Error Code F10

Contents

I was wondering if there is anything that I can test or diagnose from the front, without pulling the oven out from the wall? It is a lot of money but the worst part of it is that usually manufacturers will stop to make them in a few years after they made such model. kimberly // Feb 26, 2015 at 6:22 pm Hi I have a frigidaire gas oven model LFGF3014LBC and have been getting f10 error for a while and now just started getting So the EOC and clock/timer is the same part and looks like it would need to be replaced. Check This Out

NOTE: Before you will proceed with any tests, disconnect power for at least a minute. Very likely the problem is a faulty relay board. Gene // Feb 26, 2015 at 6:54 pm Hello Kimberly, Thank you for your question. Check wiring in probe circuit for possible open condition.

Frigidaire Oven F10 Reset

Frank // Mar 10, 2015 at 7:45 am Gene, Thank you for the advice. I pressed the cancel button, but the error comes back. We use the stove top but not the oven (not in over 18 months).

I can not tell you how long it will last but sooner or later it will die. Thus the question is : are you really like this range and going to keep it or you will replace it as soon as the control panel will die? sensor??? Frigidaire Oven Error Codes Schließen Weitere Informationen View this message in English Du siehst YouTube auf Deutsch.

Any suggestion is highly appreciated. Frigidaire Oven F10 Beeping Examples: Try searching again: Model Number GO Can't find your model number? Or do you think there may be more to the problem? F10 is a "Runaway Temperature" alarm. (If you look on the back of your stove, there should be a little envelope taped on to the sheet metal with an electrical schematic

It gives me the F10 error sporadically. Frigidaire Rtd Sensor I found them for you: "Each oven temperature can be individually adjusted. The content in this area cannot be displayed because your browser has JavaScript disabled (or does not support it, not common). So to confirm when we get an appliance repair person to come next week, what exactly should we say needs to be repaired, and will the repair person need to order

Frigidaire Oven F10 Beeping

Tags: Oven error codes 232 responses so far ↓ Ron Hirtz // Nov 16, 2013 at 7:26 pm I have the F10 error code ohm reading at the plug into the F11 - Shorted keypad. Frigidaire Oven F10 Reset I need to know how to re attach it. 4 answers Related Questions'> have mef352bgwd frigidair range/oven. What Does F10 Mean On A Frigidaire Oven You can order it at www.repairclinic.com.

Thanks Larry Gene // May 20, 2015 at 3:07 pm Hello Larry. his comment is here I came to the conclusion that the E.O.C., or Electronic Oven Control, needs to be replaced (at least I hope so since that's the part that I ordered). Today we’re going to talk about range error code F10. All of the touch screen buttons still work, so should I be concerned? Frigidaire Eoc

Thanks again and merry Christmas! Use the "Search by the model number" link bellow to see if your range has a such part. Press START to accept the temperature change and the display will return to the time of day. this contact form i found some information for you that i am hoping will help you until your expert answers your question.

What part do I need to replace it 2 answers Popular Products in Ranges Range Kleen Replacement Drip Pan 2 pack - ... Frigidaire Stove F11 Error When I searched for a part it appears you can't just replace the ribbon connector, but have to replace the whole TST panel ($600!!). The part number for the triple heating element is 316216703 Good luck." Ed // Apr 24, 2015 at 3:18 pm Hi Gene.

Gene // Mar 29, 2015 at 6:41 pm Hello MML, Sorry for the delay.

George // Dec 19, 2014 at 10:54 am Hi Gene, thanks for the reply! It may appear you are at 350 on the control but the oven is actually hotter because the sensor is bad. Michele // May 7, 2015 at 7:38 am Hi Gene, I have a Frigidaire Gallery series, gas stove, Model Number #FGGF3076KB . Frigidaire Stove F1 Error The EOC board was recently replaced (F10 went away after new board was installed, but now it is back).

If this error code shown while the oven was in day time mode, the EOC would need to be replaced. F30 Open RTD sensor probe or wiring problem. do you still suspect the relay board 316443925 ? navigate here Keep me posted.

If your probe measures 2500 ohms or higher, then a defective temperature sensor is causing this problem. All Electronic Oven Controls (EOC) have ability for self diagnosis. Thus if any of them failed, the whole heating element would need to be replaced. The part number for the EOC is 316418720 You can order the part by clicking on the part number.

Any help would be much appreciated. Severe overheating may require the entire oven to be replaced should damage be extensive. Just curious how did you note the difference in temperature? The wires look OK (no visible external wear) from the plastic connector in the back of the EOC module down to the metal bracket holding the RTD temperature sensor into the

This error code indicates a failed potentiometer for LF burner, a user interface board or the harness between the mother board and the user interface boards. Can you tell me what could be causing this error code and what parts I'll need to replace? Gene. https://www.dropbox.com/s/afvfo1xuvvrlsef/Electric%20slide-in%20range%20-%20control%20panel%20and%20EOC%20removal%20part%201.doc?dl=0 https://www.dropbox.com/s/uyrdx536z25aege/Electric%20slide-in%20range%20-%20control%20panel%20and%20EOC%20removal%20part%202.doc?dl=0 https://www.dropbox.com/s/ntcglkxlq82agdk/Electric%20slide-in%20range%20-%20control%20panel%20and%20EOC%20removal%20part%203.doc?dl=0 Keep me updated.

If the error code shown on your oven display leads to a possible problem with oven temperature sensor, start the troubleshooting from testing the temperature sensor resistance. The lower oven has no issues. If oven continues to overheat when the power is reapplied, replace the EOC. Gene // Sep 14, 2015 at 6:59 pm Hello Jack, Sorry for the delay.

Ask a Technician for Answers ASAP Ask an Expert Home Improvement Questions Appliance Repair How JustAnswer Works: Ask an Expert Experts are full of valuable knowledge and are ready to help Your welcome. Gene. So should my next step be to get a new EOC?

It was the larger ribbon connector on the right. Most codes will clear when you disconnect the power to the range for one to two minutes. The part number for the temperature probe is 316217002 Otherwise the EOC would need to be replaced. Gene // Jan 3, 2015 at 7:48 pm Hello Sharon, Sorry for the delay.