Home > Frigidaire Oven > Frigidaire Professional Series Range Error Codes

Frigidaire Professional Series Range Error Codes


Gene. It's possible that you need to replace the electronic control board or the temperature sensor. This time the relay board will likely need to be replaced again but where last time the fault was visibly on the board, this time the burn was on the pins What are your thoughts? http://blogeurope.net/frigidaire-oven/frigidaire-professional-series-oven-f3-error.php

You can order them from AppliancePartsPros.com by clicking on the following link. Replaced temp probe and same thing. Would the most likely problem be the temp. Per your advice (regarding Frigidaire stove model LFGF3014LWC), I cut the plastic connectors off and spliced the wires together making sure that the violet wires from the EOC side matched the

Frigidaire Oven F11 Error Code

Ste. 500, Encino, CA 91436 1-877-477-7278 Tennessee 240 Edwards St. The part number for the temperature probe is 316490000 If the reading is normal, the EOC has failed and would need to be replaced. https://www.dropbox.com/s/afvfo1xuvvrlsef/Electric%20slide-in%20range%20-%20control%20panel%20and%20EOC%20removal%20part%201.doc?dl=0 https://www.dropbox.com/s/uyrdx536z25aege/Electric%20slide-in%20range%20-%20control%20panel%20and%20EOC%20removal%20part%202.doc?dl=0 https://www.dropbox.com/s/ntcglkxlq82agdk/Electric%20slide-in%20range%20-%20control%20panel%20and%20EOC%20removal%20part%203.doc?dl=0 Keep me updated.

By the wiring diagram for your range, both oven heating elements getting power from the EOC. Disconnect the wire harness from the sensor. Click here to visit Merchant's home page. Frigidaire Eoc Pull the range out of the wall and unplug it.

If all situations above do not solve problem, replace EOC. Frigidaire Oven Error Code F30 Gene. I did this and it didn't work. Ever had this problem?

View Cart| Contact Us| Track Order| Customer Service| My Account Discuss error code f30in Oven Repair (including Ranges and Cooktops). "I had the same issue as macao. Frigidaire Oven F10 Reset The content in this area cannot be displayed because your browser has JavaScript disabled (or does not support it, not common). When did you replace the EOC? The part number for the porcelain wire nuts (pack of 10) AP3440631 Good luck.

Frigidaire Oven Error Code F30

Disconnect power, wait 10 seconds and reapply power. So should my next step be to get a new EOC? Frigidaire Oven F11 Error Code Disconnect the power to the oven. Frigidaire Oven Error Codes darlene // Dec 19, 2014 at 7:03 pm The frigidaire stove my son has has a f10 code.

Residential Wiring - The Right Way! navigate here Please keep me posted. You can find it on the range frame behind the bottom drawer. All rights reserved. Frigidaire Oven F10 Error

Click here to see a video that will walk you through that process. Veröffentlicht am 01.10.2015This video from Sears PartsDirect shows you what to do if your range is displaying error code F10. If it does, I would recommend to order both of them because it's very hard to remove faceplate and reattach it without damaging the part. Check This Out Diese Funktion ist zurzeit nicht verfügbar.

Neil // Apr 4, 2015 at 11:09 am Hi Gene, I have read through all of the postings on this page however I am unable to figure out the issue with Frigidaire Oven F10 Beeping Watchdog - a combination of hardware and software which acts as an internal scheme, disconnecting the systems output from the process in the event of a malfunction. Our cooking manuals cover a wide selection of gas and electric models of ovens and cook tops, ranges and stoves, self-cleaners and convection ovens.


ft. OK, Continue Tips for finding your unique model number Look for your model sticker, tag or plate. FGGF3076KBK. Frigidaire Stove Error Codes F7 By reading any content on this site you agree to AppliancePartsPros.com , Inc.

Bitte versuche es später erneut. Everything works fine. I ran the self clean on my electrolux and within 2 weeks of using my oven again, I had the F10 runaway temperature alarm. this contact form I'm lucky because it did not happen to me, but I have heard about such problems.

But it would not hurt if you will eliminate those plugs and splice the wires using a high temperature porcelain wire nuts. If you order them from AppliancePartsPros.com, you can return unneeded part later with full refund. When I used the oven the next day to heat taco shells, it got really hot (burnt them to chars!) and then the F10 code went off again- this time I Please try the request again.

Crystal // Mar 17, 2015 at 7:45 pm Hello, I have a Frigidaire Model#FGF337ABJ. Especially since the EOC had failed once before on warranty (it completely burned out and wouldn't work at all) and the repair tech told me that self clean was likely to F2 Oven temperature too hot Check and replace oven temperature sensor (RTD). Just call their customer service.

Most likely there is only one problem caused by the faulty EOC, but there is a very small chance for the latch motor to fail as well. If the igniter glows but the gas doesn't flow, possible the igniter itself is to weak to open the gas safety valve. Thanks again and happy New Year! Gene // Mar 15, 2015 at 7:12 pm Hello Robert, Sorry for the delay.