Home > Frigidaire Oven > Frigidaire Oven F31 Error

Frigidaire Oven F31 Error

Contents

When we were changing out the EOC one of the ribbon connectors (that connects the EOC to the TST control panel) pulled apart. My range is a CEW30ef6gsc. Check for continuity between the two probe wires. Do you have a suggestion as to which board is acting up? have a peek here

Steve // Mar 29, 2015 at 8:13 pm Hi, I have a frigidaire oven Model #FES355EBA , I am getting the F10 error only when oven is on, does not error What Your Appliance Error Code Really Means. The good part of this sad news is that you got nice opportunity for a good New Year (or may be it's not too late for Christmas?!) present to your wife Content Relevant URLs by vBSEO ©2011, Crawlability, Inc.

LinkBack LinkBack URL About LinkBacks Bookmark & Share Digg this Thread!

Frigidaire Gas Range F10 Error Code

The cause of this problem most likely is a faulty EOC. or Is it something else that's causing this problem? Starts beeping then stops and starts again after a while. The EOC that we ordered was 316576600.

SO PLEASE WRITE ME BACK AND HELP ME!!!! The part number for the EOC is 316576604 and you can order the part by clicking on the part number. Thanks again for all your time and help!! Frigidaire Gas Range F3 Error Ed // Apr 27, 2015 at 11:01 am Hi Gene, Per your suggestion, I cut the 2 violet wires (the 2 running between the EOC and the RTD temperature sensor) and

Thank you in advance!! replied4 years ago. Still not working but the igniter fires up now. Valerie // Apr 24, 2015 at 7:00 am Hi Gene, I am having problems again and before I order on my diagnosis, I wanted your confirmation.

I decided just to keep the range unplugged until the new EOC is installed. Eoc Frigidaire Oven There are four of them, one for each surface element. The other night after I used the broiler, it started beeping and flashing the F10 code. The controller does not see the motor rotating.  Press clear key.

F31 Error Code Kenmore Oven

Thanks Stephanie Related ModelsTappanTGF328GSGGAS RANGETappanTGF328GSHGAS RANGEFrigidaireTGF330WCDATap(v1) / Gas RangeFrigidaireTGF330WCDBTap(v1) / Gas RangeFrigidaireTGF330WCDCTap(v1) / Gas RangeFrigidaireTGF330WCDDTap(v1) / Gas RangeFrigidaireTGF330WCDETap(v1) / Gas RangeFrigidaireTGF330WCWATap(v2) / Gas RangeFrigidaireTGF330WCWBTap(v2) / Gas RangeFrigidaireTGF330WCWCTap(v2) / Gas RangeFrigidaireTGF330WCWDTap(v2) / MML // Mar 26, 2015 at 7:17 am Hi Gene, I have an Electrolux 30″ Free Standing Electric Range; model EI30EF55GSA, serial VF80822824. Frigidaire Gas Range F10 Error Code At the same time make sure the wire harness from the probe to the control panel is not damaged. Frigidaire Oven Error Codes About Us Our Community Our Blog Advertise With Us © Copyright 2015 OwnerIQ, Inc.

Remove the rear panel and locate the relay board. navigate here The part number for the temperature probe is 316217002 The part number for the EOC is 318414213 Good luck. Eric Johnson // Jan 4, 2015 at 1:10 pm You can disregard my question, thanks to your troubleshooting steps on this page, I managed to isolate the problem and repair my The correction for this problem is to replace the EOC. Frigidaire Rtd Sensor

Locate the temperature sensor (RTD) plug on the control board (EOC). If the reading is incorrect, the temperature sensor would need to be replaced. Maximum oven door lock attempts exceeded. 1. (F90, 91, 92, 93 & 94) Check the wiring between EOC & Lock Motor Micro Switch. 2. (F90, 91, 92, 93 & 94) Replace Check This Out If resistance does not match the chart, replace the RTD sensor probe.

The cause of the problem can be a faulty potentiometer or a faulty User Interface Board. Frigidaire Stove Beeping F10 Especially since the EOC had failed once before on warranty (it completely burned out and wouldn't work at all) and the repair tech told me that self clean was likely to Thanks.

I replaced the EOC and it has been fine for about 3 months and now is doing it again.

I would recommend to eliminate the sensor plug and splice the sensor into the wire harness using a high temperature wire nuts. I bought laser thermometer for the oven and it would verify the lower temperature. See Details Frigidaire FFEW2425QS 24'' Single Electric ... Frigidaire Oven Temperature Sensor Thanks again!

You may want to check the igniter by measuring the current drawn by the igniter. It is a Frigidaire Model # FFEF3048LS Any help appreciated! The time now is 06:17 PM. http://blogeurope.net/frigidaire-oven/frigidaire-gas-oven-f10-error.php I will show you how to diagnose and fix them depending on the fault code.

If the reading is wrong, replace the probe. Can you suggest a fix for this? Gene. If it's not, replace the sensor, otherwise you need to replace your relay board.

Get more answers from the people in your networks Tags Frigidaire , Ranges , Wall Ovens , Appliances Click to remove this tagging. Eric Johnson // Jan 3, 2015 at 7:30 pm I have a Frigidaire FPES3085KFC that started throwing F30 during a self-cleaning cycle. Robert Wilson // Mar 11, 2015 at 5:18 pm Hi Gene, i have a frigidaire stove model cfef366emh , it has given me an error f11 , i did disconnect the Very likely the heating element for this burner would need to be replaced but, because the part is really expensive, you may want to check the central coil for continuity prior

Now we are getting F31 error code even in the middle of the night.