Home > Frigidaire Oven > Frigidaire Gas Oven F10 Error

Frigidaire Gas Oven F10 Error

Contents

Codes flashing are F 7 and 20. It measured 1050 ohms, we then tested it back at the EOC, same reading. Can you suggest a fix for this? I’m glad to help you again. have a peek here

Jim // Dec 8, 2014 at 1:00 pm Hi Gene. The stove top and the clock work fine once we clear the PF code. The part number for the overlay is 316419141 You can order them by clicking on the part numbers. The good part of this sad news is that you got nice opportunity for a good New Year (or may be it's not too late for Christmas?!) present to your wife

Frigidaire Oven F10 Beeping

These parts are: Electronic Oven Control (EOC) and oven temperature sensor. The cause of the problem can be a faulty potentiometer or a faulty User Interface Board. If not, I understand that it is likely either the thermometer or the panel. F15 Controller self check failed.

I checked the resistance on the probe's bare wires and it reads 1099 ohms. The potentiometers are held in place by a hex nut and lock washer. Frigidaire does not sell such harness but you can find a similar wires in a local electric or hardware store. Frigidaire Rtd Sensor Gene // May 12, 2015 at 10:39 pm Hello Michele, More likely the problem is a faulty EOC because the error code came up when the door lock was not used.

Then when we started removing the relay board we found out it was fried (black soot). Good luck. Gene. I'm lucky because it did not happen to me, but I have heard about such problems.

Especially since the EOC had failed once before on warranty (it completely burned out and wouldn't work at all) and the repair tech told me that self clean was likely to Frigidaire Oven Error Codes You should replace the sensor. Happy holidays to you and your loved one as well! note: disconnect the power cord from the power source before servicing your range.

Frigidaire Oven F10 Reset

Mike Ask Your Own Appliance Question Customer: replied6 years ago. Jeff // Apr 21, 2015 at 5:20 pm Ew30ew5cgs5 model number. Frigidaire Oven F10 Beeping A defective temperature sensor can also cause this problem. What Does F10 Mean On A Frigidaire Oven By cxanthos in forum Whirlpool/Roper Replies: 1 Last Post: April 29th, 2009, 11:28 AM Frigidaire Single Wall Oven Model# FEB30S7DCB, went blank By msarbpd in forum Frigidaire/Tappan/Electrolux Replies: 4 Last Post:

Ugly is the new Sexy! navigate here If the reading at the sensor is correct, the wiring between the sensor and the control is defective. Gene. I was not aware of a door lock (because I don't see anything to slide) other than the "lock" symbol on the control panel that I've never used… Can you tell? Frigidaire Eoc

thank you for using manage my life. 1 Share theConversation Click to Chat We're available to chat FAQs Check out the most frequently asked questions Video How to use the site Jeff // Jul 17, 2015 at 2:59 pm Hi i'm having a problem with my Frigidaire oven professional series model number PLES389ECH I've followed your assessment steps with the following findings This error code indicates a failed potentiometer for LF burner, a user interface board or the harness between the mother board and the user interface boards. Check This Out Our oven flashed F10 and went into runaway temps.

Learn More for questions or assistance, call 1-800-252-1698 (Se Habla Español) M-F 6:30 a.m. - 10:00 p.m. F10 Error Code Kenmore Oven Gene. Is there a relay pack that I should be looking at?

Eric Johnson // Jan 3, 2015 at 7:30 pm I have a Frigidaire FPES3085KFC that started throwing F30 during a self-cleaning cycle.

Sorry for the delay. You can find it on the range frame behind the bottom drawer. Thus the solution is to replace it. Frigidaire Stove F1 Error Should I replace the EOC?

My wife was doing some Xmas baking and set oven to 350 and about 10 minutes into the baking the oven started beeping and the F8 code came up. I checked the RTD temperature probe at the plastic connector (1083 - 1100 ohms). If the error code shown on your oven display leads to a possible problem with oven temperature sensor, start the troubleshooting from testing the temperature sensor resistance. this contact form model plgf389cce Frigidaire professional series Gene // May 17, 2015 at 6:34 pm Hello Greg.

We turn the oven on and when it reaches a certain temperature, this code comes on and the oven cuts out. Share this conversation Expert: Mike replied6 years ago. The content in this area cannot be displayed because your browser has JavaScript disabled (or does not support it, not common). I was out of town. By the wiring diagram for your range, both oven heating elements getting power from the EOC.

The RTD part number is 316490001 The EOC part number is 316418704 Thank you for your question. Let the oven cool down and restart the function. Thanks! Bill Newberry 13,337 views 4:11 How to Fix an F1 Error On a Kenmore or GE Range - Duration: 11:41.

the fault code "f10" indicates a runaway oven temperature. Gene // Mar 15, 2015 at 7:23 pm Hello Frank, I do not think this is common with Frigidaire ovens. Code Cause - Condition Suggested corrective action F10 Control has sensed a potential runaway oven condition. THanks!

Your stove is new and suppose to be covered under manufacturer warranty. They are operated by knobs.