The time now is 06:21 PM. We bit the bullet and bought the EOC, I installed it….and have had no change in operation :(. Terms & Conditions 78ms USEQ\WEB18 Otherwise the EOC is the culprit. have a peek here
The part number for the EOC is 316455410 The part number for the overlay is 316220725 You can view and order them by clicking on the part numbers. Examples: Try searching again: Model Number GO Can't find your model number? All Electronic Oven Controls (EOC) have ability for self diagnosis. If there are some relays on it, replace the EOC.
Valerie Gene // Dec 19, 2014 at 11:42 am Hello Valerie, Sad story. If the problem persists, replace the EOC. What was wrong at that time?
Thanks Reply With Quote May 28th, 2011,09:51 PM #10 Jake View Profile View Forum Posts Visit Homepage Appliance Tech - Admin Join Date Aug 2004 Location McMullen Valley, Arizona Posts 79,575 Good luck. She noticed the oven was cooking very hot. Frigidaire Rtd Sensor The part number for the EOC is 316418720 You can order the part by clicking on the part number.
model plgf389cce Frigidaire professional series Gene // May 17, 2015 at 6:34 pm Hello Greg. Frigidaire Oven Error Codes With this info. The temperature sensor part number 316217002 The relay board part number 316429800 This part is on back order. They ship overnightJACUSTOMER-nuon2qee- :Where is the breaker located and the plug?esequiel walker :The breaker is normally outside the house on the mains.
Is there anything internal to the oven where we could turn off the appliance?esequiel walker :No just unplug it. Thank you for your question. Frigidaire Oven F10 Beeping So it's not so hard to believe. What Does F10 Mean On A Frigidaire Oven Severe overheating may require the entire oven to be replaced should damage be extensive. 2. (F11, 12 & 13) Disconnect power, wait 30 seconds and reapply power. 3. (F11, 12 &
It is a lot of money but the worst part of it is that usually manufacturers will stop to make them in a few years after they made such model. navigate here As soon as I turn on the oven it started flashing the F30 error. I washed the surface of the stove earlier today and when I turned the oven on it shot a flame out where the heat and condensation come out on top. Had to cut the power at the circuit breaker to stop the beeping. Frigidaire Eoc
The porcelain wire nuts part number is AP5641944 Good luck. I decided to pull off the rear cover and take a peak and found a portion of the Oven Control Board was burnt/charred. Jake I had no problems for the last 8 months. Check This Out Ed Gene // Apr 23, 2015 at 9:29 pm Hello Ed, Thank you for your question.
Phil // Jul 19, 2015 at 5:38 pm Hi Gene, We have a Frigidaire slide in stove/oven model no: CGES387AS5. F10 Error Code Kenmore Oven Gene // Dec 21, 2014 at 12:39 pm Hello James, Unplug the range or turn off the range circuit breaker for a few minutes and reapply power. This part is usually located on the back wall in the upper part of the oven cavity but it can be easy tested from the EOC.
These products weren't available when I was working so I don't have first hand knowledge. Check wiring in probe circuit for possible open condition. If you see any discoloration on the breaker connections, replace it. Frigidaire Stove F1 Error Yes, the temperature sensor tests OK.
The temperature may be increased as much as 35°F (19°C). 4. Where did you get the EOC you replaced recently? The relay board is obviously much cheaper than replacing the range and I hate the environmental component contributing to a landfill but at what point do you throw in the towel this contact form Gene // Jun 18, 2015 at 4:49 pm Hello Connie.
Phone Numbers, Locate a Warranty Dealer/Service Manufacturers' Web Sites Measurement Conversion Chart Need to Complain? Jake Appliance Repair School 1987-1988 Star Appliance Tech. 2 yrs. 1988-1990 Wards Appliance Tech. 11 yrs. 1990-2001 Sears Appliance Tech. 4 yrs. 2001-Oct. 2005 Jake's Appliance Repair Nov. 2005-present Look-Up & Valerie Gene // Dec 19, 2014 at 12:58 pm Valerie, Looks like the problem is a faulty oven relay board. Gene // Dec 19, 2014 at 11:35 am Hi George, I believe the relay board will solve the problem.
Today we’re going to talk about range error code F10. The resistance reading on the sensor should be close to 1100 ohms at a room temperature of 75 degrees. Sorry for the delay. If fault returns when power is reconnected, continue the troubleshooting.