Home > Frigidaire Oven > Frigidaire Error F10

Frigidaire Error F10

Contents

Mike Mike and other Appliance Specialists are ready to help you Ask your own question now Customer: replied6 years ago. Your range may be different. Ed // Apr 23, 2015 at 6:03 am Hello Gene. thanks josh Gene // Apr 10, 2014 at 5:03 pm Hello Josh. Check This Out

John // Apr 7, 2015 at 3:52 pm When I unplug the ribbon from the EOC the F11 goes away and doesn't beep anymore, can I get away with just replacing Ken Gene // Dec 26, 2014 at 1:53 pm Hello Ken, Looks like the cause of the problem is a faulty EOC. To save time you may want to order both parts together. Get more answers from the people in your networks Tags Frigidaire , Ranges , Appliances Click to remove this tagging.

Frigidaire Oven F10 Reset

Credentials confirmed by a Fortune 500 verification firm. I decided to pull off the rear cover and take a peak and found a portion of the Oven Control Board was burnt/charred. Ken // Dec 28, 2014 at 1:36 pm Hello Gene, Thank you for the info..

this video will show you how to complete the test: oven probe test . at room temperature; the sensor should measure approximately 1100 ohms of resistance. Looks like it's time for a new range. Frigidaire Oven Error Codes What's next?

Before we fix it, we need to figure out what caused it. Frigidaire Oven F10 Beeping S.E., Cleveland, TN 37311 Legal Notice|Privacy Notice©1999 - 2012Appliance Parts Pros.com«. Learn More guaranteed fit All parts are manufacturer-approved, to ensure proper fit and to keep appliances running for years to come. I do have several boards.

Suddenly, the oven has stopped working 2 answers Related Questions'>My Kenmore electric range start beeping and display F 90 error on the screen. Frigidaire Rtd Sensor Inspect the overlay. Wird geladen... To test operation of the potentiometer m Sp├Ąter erinnern Jetzt lesen Datenschutzhinweis f├╝r YouTube, ein Google-Unternehmen Navigation ├╝berspringen DEHochladenAnmeldenSuchen Wird geladen...

Frigidaire Oven F10 Beeping

roy // Mar 28, 2015 at 7:30 am i have a frigidaire stove model# pfef373es2 and it was flashing f11 so i replaced the eoc and worked for 1 day and The part number for the EOC is 316557205 The part number for the overlay is 316419303 Good luck and keep us posted. Frigidaire Oven F10 Reset Usually a few hours or so after it has been shut off. What Does F10 Mean On A Frigidaire Oven This time the relay board will likely need to be replaced again but where last time the fault was visibly on the board, this time the burn was on the pins

Usually an hour or so after it has been shut off. http://blogeurope.net/frigidaire-oven/frigidaire-f5-error.php She has had repeated problems with it stopping, locking up in the model of cooking, turning off, etc. Any other suggestions? thank you….tom Gene // Sep 7, 2015 at 9:32 pm Hi Tom, Thank you for your question. Frigidaire Eoc

A defective temperature sensor can also cause this problem. Thanks Larry Gene // May 20, 2015 at 3:07 pm Hello Larry. The part number for the EOC is correct. http://blogeurope.net/frigidaire-oven/frigidaire-f10-error-fix.php If the reading is correct, test operation of the potentiometer by measuring the resistance between pin terminal G (center) and either of the outside pin terminals as the control shaft is

If the reading is incorrect and the wires and plugs between the sensor and the EOC are good, replace the temperature sensor (RTD probe). Frigidaire Stove F11 Error When replacing a potentiometer, do not over-tighten the hex nut. If it would not fix the problem you have up to 365 days to return the part for full refund.

Also, if it would not and you ordered the part from AppliancePArtsPros.com, you can return it within 365 days.

You can get it from AppliancePartsPros.com for $558.91. By reading any content on this site you agree to AppliancePartsPros.com , Inc. I checked the resistance on the probe's bare wires and it reads 1099 ohms. Frigidaire Stove F1 Error the oven temperature sensor can be removed and tested for resistance and compared to the rtd scale in the image below.

Click here to visit Merchant's home page. If the meter shows a resistance of less than 1000 ohms or more than 1300 ohms at room temperature, the sensor will have to be replaced. Unfortunately this part has been discontinued by the manufacturer and is no longer available. http://blogeurope.net/frigidaire-oven/frigidaire-f30-error.php At room temperature, most Frigidaire oven temperature sensor probes will measure about 1100 ohms at room temperature.

It is just run away heat. I managed to push them back into the cap, and we were able to reconnect it to the EOC board, but at least one of them broke off. Check for continuity between the two probe wires. I would suggest to call Frigidaire for service.

We ordered both the parts, tried the EOC first, with no fix. If there is nothing wrong with the wires, send me the part numbers for the EOC and RTD you replaced. How can I fix it. .....The beeping is driving me crazy 1 answer Related Questions'>I have a Kenmore electric stove/oven model # 790.94222409. Contact the seller and request the replacement.

Click here to visit Merchant's home page. Good luck. The question I have is : does the oven control sensor store these failures ? Measure the resistance between these wires.

Code f10. Gene // Dec 2, 2014 at 10:00 pm Hello Steve, Sorry to hear you have more problems with your range. The keypad would not stop beeping and flashed an F11 code. If the lock switch is defective, replace motor lock assembly.

In such situation the only solution is to replace the EOC. Thanks again and merry Christmas! Ed // Apr 27, 2015 at 11:01 am Hi Gene, Per your suggestion, I cut the 2 violet wires (the 2 running between the EOC and the RTD temperature sensor) and greg // May 17, 2015 at 3:58 pm I got an f1 error code in the middle of baking in the oven.

What part do I need to replace it 2 answers Popular Products in Ranges Range Kleen Replacement Drip Pan 2 pack - ... Unfortunately (fortunately for your wife =-D) this part has been discontinued and is no longer available. The new one should solve it.