Home > Frigidaire Affinity > Frigidaire Washer Error Code Pau

Frigidaire Washer Error Code Pau

Contents

Click here to visit Merchant's home page. Skip to content Sign In Join or Activate Products Departments Departments Shop Shop Explore Explore Advice Advice Rewards Rewards More More Home / Brands / Manage My Life / Questions I attached both links below. If the "Delay Start" button was pushed it allow you to program the washer to start at a later time. If you're not able to cancel the cycle by pressing the have a peek here

Ugly is the new Sexy! Wird geladen... Lots of times I see these get clogged with stuff and not drain properly, just remove the hoses that connect to it and check to see if anything is inside it. See Details Whirlpool WTW5000DW 4.3 cu.

Frigidaire Affinity Washer Stuck On Pause

Anmelden Teilen Mehr Melden Möchtest du dieses Video melden? Ask Appliance Man Your Own Question Appliance Man, Home Appliance Technician Category: Appliance Satisfied Customers: 9896 Experience: Appliance tech 4 years 13888241 Type Your Appliance Question Here... Anmelden Transkript Statistik 44.516 Aufrufe 105 Dieses Video gefällt dir? To change the current temperature, push "Pause" and wait for the PAU code to appear on the display.

Turn the program knob (9) clicks from the start position. I hope one of these helps clear the error. S. Frigidaire Affinity Door Lock Rave Reviews "I thought it was the best online shopping experience that I have ever had when it comes to parts." Eric H.

Anyway you are not getting water into the machine either from that or you have 2 (Hot and Cold) water inlet valves are bad (very rare for both to fail). Note: A letter appearing in the code stands for a number higher than nine: A = 10 B = 11 C = 12 D = 13 E = 14 F = I had so many questions and they answered them all." Sharon S. E67 Input voltage on microprocessor incorrect.

Virginia Beach, VA "Your service people are so friendly and helpful. Frigidaire Affinity Dryer Stuck On Pause Ft. Possible solution: Do not open door, ... The pau code keeps coming up.

Frigidaire Affinity Washer E41

Pressure sensor indicates water overfill. E41 Control board thinks the door switch is open. Frigidaire Affinity Washer Stuck On Pause NOTE: During normal operation, the display may show: “SAn” - deep clean (Sanitary Cycle) “cd” - cool down (Sanitary cycle) “do” or “dr” - door problem. “Err” - an error has Reset Frigidaire Affinity Front Load Washer Turn the program knob clockwise 9 clicks from the Start Position.

If it is a "PAU" code that could be an interruption within your cycle. navigate here Frigidaire Frontload Washer New Fault Codes Model differences: Better models have a digital readout display Good models do not have a digital readout display In the Better Models line, the failure Does it have anything to do with the Control Board and if so what is the part #. Here's the drain motor for your model, in case you need to order it: Drain Pump 137221600 Order now for same day shipping. 365 day return policy. E41 Error Frigidaire Washer

Now 30 10/13/2016 10/13/2016 JACUSTOMER-x0uwnnmp- I have a maytag stove mod#MERH752BAW.lock indicator light 10/13/2016 10/13/2016 md20/20 X Ask an Appliance Technician Get a Professional Answer. 100% Satisfaction Guaranteed. 40 Appliance Technicians Melde dich an, um unangemessene Inhalte zu melden. Veröffentlicht am 29.06.2013Troubleshoot a Frigidaire Washer suffering from this following dilemmas: Stuck on pause, no restart Visit us at http://www.appliancevideo.com To finish the repair you will need to use a 131763202 Check This Out Parts Search Fixitnow Site Search Search for: Appliance Repair Training and Support Proudly powered by WordPress Admin Login Learn appliance repair online from experts at the Master Samurai Tech Academy!

The author of this site has no liability for errors, omissions, or any defects whatsoever in the information or instructions, or for any damage or injury resulting from the utilization of 131763202 Door Lock So then we did some more research online and found that we should try resetting it by holding the pause/Start button and cancel buttons simultaneously and now its beeping again and Press the cancel and the start button in at the same time for 5 seconds.

ft.

The code is obtained by counting the number of times the lights flash. Ft. I am getting a PAU code and it will not continue Possible cause: inlet valve, pressure switch or control board failure. Frigidaire Affinity Washer Sensing Wird geladen...

E24 Drain pump relay on control board failed. If this code would appear on a washer in the Good model line, the five indicator lights would blink fifteen times and the START indicator light would blink once. E76 Better model only. http://blogeurope.net/frigidaire-affinity/frigidaire-affinity-washer-error-code-dr.php Step 2: Please assign your manual to a product: About Advertising About Us Blog Careers News & Media Help Contact FAQ Partners Privacy Policy Terms Community Forums Recent Q&A Top Experts

Normally means the washer has been paused, which could be cleared Prev123Next » Not finding what you are looking for? Listen for a relay closure inside the motor control shortly after the Start/Pause key is pressed. Now our 10/14/2016 10/14/2016 JACUSTOMER-x0uwnnmp- I think my husband may have broken the sensor off the flex 10/14/2016 10/14/2016 JACUSTOMER-x0uwnnmp- Frigidaire Affinity 3 blinking lights right side. Click here to visit Merchant's home page.

The content in this area cannot be displayed because your browser has JavaScript disabled (or does not support it, not common). All rights reserved. To START THE TEST: On non-digital display models, turn the Program Knob to start position, Drain/Spin. Kansas City, KS "Robin went above and beyond the call to assist me and I was very impressed." Val T.

E42 Door remains locked after cycle is completed. Press Pause Cancel to turn off LEDs. E23 Drain pump relay on control board failed. Wähle deine Sprache aus.

Example: E14. Turn the program knob (5) clicks from the start position. Hound of Baskerville Mask $12.99(Retail $17.99) It was a huge, spectral black dog, which according to legend roamed the desolate moor to avenge its mistress's death....[Read More] Appliance Parts, Accessories & Anmelden 106 4 Dieses Video gefällt dir nicht?

Press and HOLD the Start/Pause and Cancel buttons simultaneously. Exiting Diagnostic Mode There are two options for exiting the Diagnostic Test mode and returning the washer to normal operation: Unplug the power cord, wait 5-8 seconds, then reconnect the power Its very easy to get access to the drain motor. If the failure is something that the customer can correct (such as the water faucets being turned off), the washer will operate normally the next time it is started.

Click here to visit Merchant's home page. Melde dich bei YouTube an, damit dein Feedback gezählt wird. I found two web sites that offer some solutions.