Home > Frigidaire Affinity > Frigidaire Front Load Washer Error Code E5e

Frigidaire Front Load Washer Error Code E5e

Contents

what is test 11. I located the datasheet and put it in diagnostic mode. E47 Board thinks the door PTC circuit is open in spin. Check the outlet voltage. have a peek here

Speed control board, Electronic control board E5F Communication problem between the control boards Unplug the washer and check the wire harness connections between the main electronic control board and the speed Refer to test (11). Listen to this Post

Leave a Reply Cancel reply You must be logged in to post a comment. It's super easy to use and best of all - free.

Frigidaire Affinity Washer Speed Control Board

Indeed, the whole assembly was pretty clean. The door lock is humming as well but it does lock.When put into spin it does start pumping but only for a few seconds similar to it filling.customer said machine ended It does this a few times and then it does nothing else. Results 1 to 2 of 2 Thread: Frigidaire Affinity E5E Thread Tools Show Printable Version Search Thread Advanced Search Display Linear Mode Switch to Hybrid Mode Switch to Threaded Mode

E52 Bad signal from tacho generator. i unplug the machine an plugged it up again . If the motor is sound, the speed control board usually needs to be replaced. Question about Frigidaire Washing Machines 1 Answer Error code E5E error code E5E E5E is for the control board failure.

Close Member Exclusive Not a member? Frigidaire Affinity Control Board Browse Categories Answer Questions Frigidaire GLTF2940ES Front Load Washer Frigidaire Washing Machine Washing Machines All Unanswered Join Sign In Ask a Question × HomeForumWashing MachinesFrigidaireFrigidaire GLTF2940ES Front Load WasherError code e5e If this code would appear on a washer in the Good model line, the five indicator lights would blink fifteen times and the START indicator light would blink once. Check the fill lines for freezing in the winter.

For error codes that have an alpha characters in the third position, the Start light blinks 10 times for A, 11 times for B, 12 times for C, and so on. All rights reserved. © Applianceblog.com 2004 - 2014 Air Conditioners | Dehumidifiers | Dishwashers | Disposals | Dryers | Freezers | Humidifiers | Ice Makers | Microwave Ovens | Ovens, Ranges, E45 Control board problem. Question about Frigidaire Washing Machines 1 Answer What is error code e5e ...error code e5e Hello jsw1993 – Typically error code E5E indicates that there is a communication problem.

Frigidaire Affinity Control Board

If the motor is sound, the speed control board usually needs to be replaced. If the spin bearing is sound, check the resistance of the motor windings for a reading between 4 and 6 ohms. Frigidaire Affinity Washer Speed Control Board Not terribly informative, but I include this example to demonstrate how this increased complexity is making it more difficult to accurately troubleshoot these failures on new appliances. Frigidaire Affinity Diagnostic Mode Tell us how to save your model.

If the spin bearing is sound, check the resistance of the motor windings for a reading between 4 and 6 ohms. navigate here Loading...Oops :Please try again. Any help please!! So following the testing process, I verified each wiring connector between the two boards, and did a resistance check of each wire to ensure I didn't have a broken or shorted Frigidaire Washer Error Codes

Mike Back To Top PM Quote Reply Posted: Sun Feb 14th, 2010 12:46 pm PM Quote Reply 6th Post NCSU_laundry_tech Joined:Mon Aug 18th, 2008 Location:Raleigh, North Carolina USA Posts:940 If you find the wiring is good, you may need ... I removed the control board. Check This Out but nothing happens.

You can do this by unplugging it or flipping the household circuit breaker to the off position Question about Frigidaire Washing Machines 1 Answer Affinity. The content in this area cannot be displayed because your browser has JavaScript disabled (or does not support it, not common). CT Sat7:00 a.m. - 9:00 p.m.CT Sun7:30 a.m. - 9:00 p.m.CT Chat Local Store Availability Enter your zip code Find Store Sears PartsDirect uses your location to provide local availability

If the wiring harness is sound, the door lock/switch assembly usually needs to be replaced.

What does code e5e mean? it's really impossible to say. The bleach water solenoid will activate and cold water should enter through the bleach compartment. It doesn't appear to have any burns but it seems everything is pointing to a bad control board.Jadsvc1, I'm assuming I need a few aligator clips and some long wire to

If the motor has failed, replace it. E13 Water leak in tub or air leak in air bell. Washer will turn on and tries to call for water, etc.. this contact form If the drain pump is damaged, replace it.

Don't get me wrong I'm not doubting you, plus I can see you have a good rating. Ask Your Own Appliance Question Customer: replied6 years ago. http://fixitnow.com/wp/2009/10/29/troubleshooting-drive-motor-problems-in-a-frigidaire-front-loading-washer/ ____________________Need parts? Call our Parts Department now! 877-803-7957 Back To Top PM Quote Reply Posted: Sun Feb 14th, 2010 03:13 am PM Quote Reply 5th Post Coronach Grasshopper Joined:Sat Feb 13th,

Started by curtis Replies: 3Views: 11450 July 05, 2007, 09:25:04 PM by AJ Water Collecting in Boot on Select Frigidaire Front-Load Washers Started by AJ Replies: 1Views: 6035 August 05, 2013, E59 No tacho signal for 3 seconds. By Sears in forum General Appliance Chat Replies: 12 Last Post: October 24th, 2011, 07:34 PM Frigidaire Affinity Dryer By jafish in forum Frigidaire/Electrolux Replies: 3 Last Post: May 9th, 2011, Wiring good: Replace the control board.

In an event of a return, coupon savings may be deducted from your refund. If the pulley doesn't spin freely, the outer tub and spin basket usually need to be replaced because a spin bearing failed. Check for a leak in the wash tub. Electronic control board E24 Drain pump relay failed The drain pump relay on the control board failed.

Logged Having is not always so desirable as wanting . . . Electronic control board E46 Control board failure Unplug the washer for 5 minutes. It's fast and easy to create one. If the tachometer resistance is within that range, remove the drive belt.

If the voltage is normal, replace the electronic control board.