Home > Error Code > Ge Range Error Codes

Ge Range Error Codes

Contents

Wird geladen... Replace faulty part. Control boards can be purchased at AppliancePartsPros.com. Replace faulty part. this content

Tell us how to save your model. Replace if zero or infinite ohms. Sarasota, FL "Best customer service experience I ever had." Christine G. Many times, it means the keypanel needs to be replaced.F1This code usually means that there is a problem with the keypanel. http://www.appliancepartspros.com/repair-help/ge-fault-codes.html

Ge Oven Error Codes F2

As a member of Shop Your Way Rewards℠, you'll earn Rewards every time you shop. If this fault code cannot be cancelled, replace the oven control (also called clock or ERC), touch pad, or both. FD Shorted meat probe Note: Problem can be with the probe or receptacle or meat probe circuit. · Check probe.

If no over temperature condition occurred: Look for a high resistance connection or any other cause of high resistance in the oven temperature sensor circuit. All of our chat agents are currently assisting other customers. If the resistance is not within that range replace the sensor. Ge Oven Error Codes F7 E6 All rights reserved.

Now using your ohmmeter , measure resistance between the wires going to the sensor. Ge Oven Error Codes F3 Copyright © 1999-2016 , Eldis Group Partnership. If present, replace control board (clock). If no over temperature condition occurred: Look for a high resistance connection or any other cause of high resistance in the oven temperature sensor circuit.

Check the probe for pinched wires and make sure there is no condensation or contamination on receptacle. F76 Ge Oven Yes No Thanks! First disconnect power then get to the controls (on most ranges the back comes off, on ovens the front comes off). CT Sat7:00 a.m. - 9:00 p.m.CT Sun7:30 a.m. - 9:00 p.m.CT About Us Contact Us Top Parts Affiliate Program Parts Store Locations Sears Commercial Parts All Brands All Categories Appliance Parts

Ge Oven Error Codes F3

Sign In Register Keep model on this computer temporarily This option is valuable if you expect to revisit Sears PartsDirect using this computer and browser in the future.

Check drain line and drain valve in pump for debris and blockage. Ge Oven Error Codes F2 FF Loss of door motor safety switch Replace the oven control (also called clock or ERC). Ge Error Codes Washer F3 Key panel (touch pad) shorted This code will occur if a shorted key panel is detected continuously over 60 seconds.

Rave Reviews "I thought it was the best online shopping experience that I have ever had when it comes to parts." Eric H. http://blogeurope.net/error-code/ge-range-f7-error-code.php FC Problem with door lock circuit such as pinched wires between control and door lock switches on motorized lock circuits Check wiring and test operation of switches. Enjoy bottle-quality water without the added waste (stays the same) Automatic Reorder About SYWR Get rewarded for shopping. Sign in and keep model in your profile permanently Don't have a profile? Ge Oven F9 Error

F3 Key panel (touch pad) shorted This code will occur if a shorted key panel is detected continuously over 60 seconds. Close Thank you! Your satisfaction is important to Sears. have a peek at these guys If the sensor is open (or not within that range) replace sensor, if not check the wiring between sensor and control.

F2 Oven cavity thermistor closed Check oven thermistor for continuity. Ge Oven Error Code F7 If this fault code cannot be cancelled, replace the oven control (also called clock or ERC), touch pad, or both. FD Shorted meat probe Problem could be with the probe, the receptacle, or probe circuit.

C7 - Temperature Sensor Bad - Replace temperature sensor (remove door to access panel, sensor should be located inside the door).

Items received damaged must be reported within 10 days of receipt. Sensors and control boards can be purchased at AppliancePartsPros.com. C2 - Drain Line Totally Blocked - This error will occur when dishwasher is unable to pump out water within the maximum time of 405 seconds. Ge Profile Refrigerator Error Codes No other buttons work: · Check wiring harness · Check pressure sensor switch · Check circuit board 7E - Water supply error No frequency change for 60 minutes from water supply.

Replace faulty part. 7E - Water Supply Error - Press 'Power' button and check wiring harness, water valve, pressure sensor switch, and circuit board for defects. Now you should see a ribbon that connects the keypad to the control board disconnect it. Kansas City, KS "Robin went above and beyond the call to assist me and I was very impressed." Val T. http://blogeurope.net/error-code/ge-range-error-f7.php Replace if zero or infinite ohms F2 Shorted thermal sensor, will occur if a shorted thermal sensor is detected continuously over 5 seconds on convection, combination or roast cooking Check oven

Sensors and contorl boards can be purchased at AppliancePartsPros.com. I had so many questions and they answered them all." Sharon S. It should be somewhere between 1050 and 1150 ohms. Every time the system is powered up and after each clean cycle the system performs a check sum and compares the value to the value programmed into the software (stored in

Error Code Condition Check/Repair Shop Parts F0, F1 or F7 Stuck or defective button on the key panel Push the Clear/OFF pad. If the resistance is not within the range mentioned above, then replace the sensor.