Home > Error Code > Frigidaire Stove Error F31

Frigidaire Stove Error F31

Contents

She hit oven cancel and it went off but then started beeping again and the same code appeared. If the reading is correct, test operation of the potentiometer by measuring the resistance between pin terminal G (center) and either of the outside pin terminals as the control shaft is OK without a multimeter it would be just a guess but I'd replace the sensor before I replaced the control board since it's so much cheaper. But it would not hurt if you will eliminate those plugs and splice the wires using a high temperature porcelain wire nuts. http://blogeurope.net/error-code/frigidaire-stove-error-code-f11.php

The keypad would not stop beeping and flashed an F11 code. I washed the surface of the stove earlier today and when I turned the oven on it shot a flame out where the heat and condensation come out on top. Gene // Sep 14, 2015 at 6:48 pm Hello Becque Ford, Thank you for your question. All rights reserved.

Frigidaire Gas Range F10 Error Code

Gene. These ovens have very badly stamped metal inside that will cut through wiring very easily. The vast majority of oven controls, used by different manufacturers, consists of two separate parts - the electronic control board and the user interface device (keypad or touchpad). An "F31" stands for a shorted probe connection.

Remove the oven door as instructed in the Owner Guide and inspect both hinges. Answer questions, earn points and help others Answer questions Manuals & User Guides PDF Manual Http://www.warnersstellian.com/files/f... So, what elst could it be? Frigidaire Gas Range F3 Error Try resetting your appliance by unplugging it or flipping the household circuit breaker off.

If too high or low, replace oven temperature sensor F4 Oven temperature sensor shorted Replace oven temperature sensor F5, 6, 7 EOC (Electronic Oven Control) failure Replace Electronic Oven Control F8 The part number for the overlay is 316419828 Gene. Thank you! Can you please tell me, does this sound like a bad control board?

Gene. Frigidaire Stove Beeping F10 The oven was working fine until in the last couple of days the PF code would come on after the oven had been on for a while. Gene. Get more answers from the people in your networks Tags Frigidaire , Ranges , Wall Ovens , Appliances Click to remove this tagging.

F31 Error Code Kenmore Oven

Appliance Repair Aid www.applianceaid.com JRAppliance www.jrappliance.ca Reply With Quote September 13th, 2012,07:52 PM #3 trz View Profile View Forum Posts Private Message View Blog Entries View Articles Junior Member Join Date I was wondering if there is anything that I can test or diagnose from the front, without pulling the oven out from the wall? Frigidaire Gas Range F10 Error Code I would appreciate any you can provide! Frigidaire Oven Error Codes The author of this site has no liability for errors, omissions, or any defects whatsoever in the information or instructions, or for any damage or injury resulting from the utilization of

If fault returns after reconnecting power, replace the EOC. navigate here It would need to be replaced. Do not forget to remove the power from the oven prior to repair. If the sensor appears to be okay, you can check the wiring (with the range still unplugged) between the probe and the ERC (Electronic Range Control board). Frigidaire Rtd Sensor

What was wrong with the old one? Gene // Jun 18, 2015 at 4:49 pm Hello Connie. Just call their customer service. Check This Out if wiring is good, replace the EOC.

We'll help you figure it out! Eoc Frigidaire Oven Let the oven cool down and restart the function. unplugh the unit, and uscrew rear panel of the unit, there is a thermostat that may have tripped, very small maybe the size of a quarter, with 2 wires on it,

Your Own Question Tyler Z., Appliance Doc Category: Appliance Satisfied Customers: 73224 Experience: 9+ years being an appliance technician with factory training. 13574879 Type Your Appliance Question Here...

Thanks Stephanie Related ModelsTappanTGF328GSGGAS RANGETappanTGF328GSHGAS RANGEFrigidaireTGF330WCDATap(v1) / Gas RangeFrigidaireTGF330WCDBTap(v1) / Gas RangeFrigidaireTGF330WCDCTap(v1) / Gas RangeFrigidaireTGF330WCDDTap(v1) / Gas RangeFrigidaireTGF330WCDETap(v1) / Gas RangeFrigidaireTGF330WCWATap(v2) / Gas RangeFrigidaireTGF330WCWBTap(v2) / Gas RangeFrigidaireTGF330WCWCTap(v2) / Gas RangeFrigidaireTGF330WCWDTap(v2) / Any help would be greatly appreciated. This time the relay board will likely need to be replaced again but where last time the fault was visibly on the board, this time the burn was on the pins Frigidaire Oven Temperature Sensor Gene.

Neil Gene // Apr 5, 2015 at 9:46 pm Hello Neil, Thank you for your question. I don't think anything else but EOC is the main culprit. Martha tebbenkamp // Nov 29, 2014 at 5:54 am Good morning, I am writing on behalf of my 90 year old mother who has a ken more model 790 built in http://blogeurope.net/error-code/frigidaire-stove-error-codes-f7.php Saves me a trip to the store to buy the wires.

Thank you, Gene. Only by eliminating everything else until it is the last item left. The front left burner has quit working but only the center burner, not the outer two rings. Check the temperature sensor resistance as described previously.

Shorted Keypad. This particular control panel was designed for this model only. In order to determine ETA you may want to click on the following link to chat with a representative. LinkBack Thread Tools Search this Thread Display Modes #1 (permalink) 11-08-2011, 01:27 PM Zanesmom310 Junior Member Join Date: Nov 2011 Posts: 1 Error code F31 Model Number: TGF328GSFBrand:

Enjoyed reading your help to other people. Gene. Both probes check 1178-1179 OHMS at the probe and the board. Now it wont let me set the clock to the right time.

If the reading at the sensor is the same as reading at the EOC plug, the sensor is defective.