Home > Error Code > Frigidaire Gallery F11 Error

Frigidaire Gallery F11 Error

Contents

Have to pop breaker until it cools down otherwise F11 stays along with beeping and won't go away. These parts are: Electronic Oven Control (EOC) and oven temperature sensor. The content in this area cannot be displayed because your browser has JavaScript disabled (or does not support it, not common). My wife spilled some water on it and the beeping started about 10 minutes later. have a peek here

I would suggest to call Frigidaire for service. replied6 years ago. Corporal: An expert that has over 10 points. The part number for the porcelain wire nuts (pack of 10) AP3440631 Good luck.

Frigidaire Gas Range F10 Error Code

The time now is 06:16 PM. Good luck and Happy Holidays. Is it safe to leave appliance unplugged for a few days.

Posted on Sep 16, 2009 Helpful 7 Not Helpful Comment Flag You can't post conmments that contain an email address. × Comment Anonymously Video Images InstaRep Level 2: An expert who The black potentiometer should have a resistance of 10KΩ. we just put the motherboard part in - what part are you talking about? Frigidaire Stove Keeps Beeping Can it be adjusted to have it beep in sync with the actual temperature set?

Phone Numbers, Locate a Warranty Dealer/Service Manufacturers' Web Sites Measurement Conversion Chart Need to Complain? Frigidaire Range Error Codes I found them for you: "Each oven temperature can be individually adjusted. Hello,The F1 error code means a button on the touchpad is stuck,usually pushing clear/off will clear it. Valerie // Dec 19, 2014 at 11:49 am Hi Gene, The model number for the range is CEW30EF6GSC.

The email address entered is already associated to an account.Login to post Please use English characters only. Kenmore Stove F11 Error Code Copyright © 2000-2016 ApplianceAid.com. The beeping persisted so I called the repairman which will come out next week. If the problem persists, replace the EOC.

Frigidaire Range Error Codes

Keep me posted. Gene. Frigidaire Gas Range F10 Error Code The part number for the relay board is 316443925 Thank you for stopping by. Eoc Frigidaire Oven The cause of the problem in such situation most likely is a failed wire harness between the sensor and the EOC.

I can push the button in that turns off the oven light and makes the oven think the door is closed, and it will immediately start beeping and showing F11 again. http://blogeurope.net/error-code/frigidaire-gallery-oven-f11-error.php Gene // Jan 4, 2015 at 1:07 pm Hello Eric, If the problem just melted wire harness connector and the temperature probe tests out OK then the easiest solution is to Thanks, Valerie Gene // Apr 24, 2015 at 8:35 pm Hello Valerie, The heating element for this burner has three separate coils, which can be turned on in a different ways, There are no a separate keyboard or keypad on your range. F11 Error Code Electrolux Range

do you still suspect the relay board 316443925 ? If there is nothing wrong with the wires, send me the part numbers for the EOC and RTD you replaced. We were cooking and all of a sudden the error message came on. Check This Out Gene // Dec 24, 2014 at 5:31 pm Hi Ken, Merry Christmas and Happy New year to you as well!

They will also be able to assist with repairs, if needed. Frigidaire Stove Beeping F10 roy // Mar 28, 2015 at 7:30 am i have a frigidaire stove model# pfef373es2 and it was flashing f11 so i replaced the eoc and worked for 1 day and Very likely the heating element for this burner would need to be replaced but, because the part is really expensive, you may want to check the central coil for continuity prior

This error code means that EOC thinks a runaway condition exists.

Good luck. Turn off power for 30 seconds then turn power on. You only need to remove the top 2 layers. F30 Error Code Frigidaire Range I have spent lots of time researching my issue and can not find anyone else describing this particular problem.

The part with the key pads you see, is nothing else but the overlay which is glued to the EOC. You can remove power to the oven for 2 minutes and turn the power back on and see if the problem has cleared. The most likely cause of the F11 and the Try starting self clean and then waiting 60 seconds and canceling it. this contact form self-clean - Use to set the keep warm - Use to start - Use to set broil feature.

I will show you how to diagnose and fix them depending on the fault code. Older products will show only two digits F-codes, but on ranges manufactured beginning in 2004 many of EOC's will have expanded three digit fault codes. The EOC that we ordered was 316576600. The Element ON indicator lights will heat.

There is a separate membrane switch in your range which would need to be replaced in such situation. Especially since the EOC had failed once before on warranty (it completely burned out and wouldn't work at all) and the repair tech told me that self clean was likely to